Ошибка Option 'mesh_min' in section 'bed_mesh ' must be specified
здравствуйте друзья. принтер Qidi Tech Q1 Pro. помогите разобраться как исправить ошибку. Я выполнял калибровку bed mesh, и после сохранения профиля появилась ошибка — Option 'mesh_min' in section 'bed_mesh ' must be specified.
Вроде как mesh min стоит. я в этом деле новичок.
вот конфигурация принтера:
# Q1_Pro
# V4.4.14 2024-3-14
# update: heater_generic hot -> chamber
# out_put_pin fan0 -> fan_generic cooling_fan
# out_put_pin fan2 -> fan_generic auxiliary_cooling_fan
# out_put_pin fan3 -> fan_generic chamber_circulation_fan
# heater_fan hot -> heater_fan chamber
# verify_heater hot -> verify_heater chamber
# V4.4.17 2024-3-29
# update: delete comments
# add time_update macro
# [bed_mesh] 6,6 ->8,8
# V4.4.19 2024-4-16
# update: add [chamber_fan chamber_fan]
# V4.4.20 2024-6-17
# update: [smart_effector]
# samples_result: average -> submaxmin
# speed: 10 -> 5
# sample_retract_dist: 3.0 -> 5.0
# [stepper_x]
# position_max: 245 -> 246
[include timelapse.cfg]
[include Adaptive_Mesh.cfg]
[include gcode_macro.cfg]
[include plr.cfg]
[include time_update.cfg]
[mcu]
serial: /dev/ttyS2
restart_method: command
[mcu U_1]
serial: /dev/ttyS0
restart_method: command
[respond]
default_type: echo
[save_variables]
filename =/home/mks/klipper_config/saved_variables.cfg
[resonance_tester]
accel_per_hz: 150
max_smoothing:0.5
[duplicate_pin_override]
pins:
gpio21 ,U_1:PC3
[bed_screws]
screw1:10,10
screw1_name: Front left
screw2: 230,10
screw2_name: Front right
screw3: 125,240
screw3_name: Last right
[screws_tilt_adjust]
screw1:-5,5.6
screw1_name: Front left
screw2: 216,5.6
screw2_name: Front right
screw3: 103,235.6
screw3_name: Last right
screw_thread: CW-M4
[force_move]
enable_force_move : false
[hall_filament_width_sensor]
adc1: gpio27
adc2: gpio28
cal_dia1: 1.50
cal_dia2: 2.0
raw_dia1: 14397
raw_dia2: 15058
default_nominal_filament_diameter: 1.75
max_difference: 0
measurement_delay: 50
enable: false
measurement_interval: 10
logging: False
min_diameter: 0.3
use_current_dia_while_delay: False
pause_on_runout:True
runout_gcode:
RESET_FILAMENT_WIDTH_SENSOR
M118 Filament run out
event_delay: 3.0
pause_delay: 0.5
[extruder]
step_pin:gpio5
dir_pin:gpio4
enable_pin:!gpio10
rotation_distance: 53.7 #22.6789511 #Bondtech 5mm Drive Gears
gear_ratio: 1517:170
microsteps: 16
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
min_temp: 0
max_temp: 360
min_extrude_temp: 175
smooth_time: 0.000001
heater_pin:gpio24
sensor_type:MAX6675
sensor_pin:gpio17
spi_speed: 100000
spi_software_sclk_pin:gpio18
spi_software_mosi_pin:gpio19
spi_software_miso_pin:gpio16
max_power: 1
control : pid
pid_Kp=33.555
pid_Ki=4.76
pid_Kd=59.141
pressure_advance: 0.032
pressure_advance_smooth_time: 0.03
max_extrude_cross_section:500
instantaneous_corner_velocity: 10.000
max_extrude_only_distance: 1000.0
max_extrude_only_velocity:5000
max_extrude_only_accel:2000
step_pulse_duration:0.000002
[tmc2209 extruder]
uart_pin:gpio6
interpolate: True
run_current: 0.714
stealthchop_threshold: 0
[adxl345]
cs_pin:gpio13
spi_software_sclk_pin:gpio14
spi_software_mosi_pin:gpio15
spi_software_miso_pin:gpio12
axes_map: -x, z, -y
[printer]
kinematics:corexy
max_velocity: 600
max_accel: 20000
max_accel_to_decel: 10000
max_z_velocity: 10
max_z_accel: 500
square_corner_velocity: 8
[stepper_x]
step_pin:U_1:PB4
dir_pin:!U_1:PB3
enable_pin:!U_1:PB5
microsteps:16
rotation_distance: 39.88
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
endstop_pin:tmc2240_stepper_x:virtual_endstop
position_min: -5.5
position_endstop: -5.5
position_max:246
homing_speed:50
homing_retract_dist:0
homing_positive_dir:False
step_pulse_duration:0.0000001
[stepper_y]
step_pin:U_1:PC14
dir_pin:!U_1:PC13
enable_pin:!U_1:PC15
microsteps: 16
rotation_distance: 39.88
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
endstop_pin:tmc2240_stepper_y:virtual_endstop
position_min: -4.5
position_endstop: -4.5
position_max: 258
homing_speed:50
homing_retract_dist:0
homing_positive_dir:False
step_pulse_duration:0.0000001
[stepper_z]
step_pin:U_1:PC10
dir_pin:U_1:PA15
enable_pin:!U_1:PC11
microsteps: 128
rotation_distance: 4
full_steps_per_rotation: 200
endstop_pin:probe:z_virtual_endstop #U_1:PC3 for Z-max
endstop_pin_reverse:tmc2209_stepper_z:virtual_endstop
position_endstop:-0.2
position_endstop_reverse:248
position_max:248
position_min: -9
homing_speed: 8
homing_speed_reverse: 8
second_homing_speed: 10
homing_retract_dist: 5.0
homing_positive_dir:false
homing_positive_dir_reverse:true
step_pulse_duration:0.0000001
[stepper_z1]
step_pin:U_1:PB1
dir_pin:U_1:PB6
enable_pin:!U_1:PB0
microsteps: 128
rotation_distance: 4
full_steps_per_rotation: 200
step_pulse_duration:0.0000001
endstop_pin_reverse:tmc2209_stepper_z1:virtual_endstop
[z_tilt]
z_positions:
-59,125
307.5,125
points:
0,125
215,125
speed: 150
horizontal_move_z: 5
retries: 2
retry_tolerance: 0.05
[tmc2240 stepper_y]
cs_pin:U_1:PB9
spi_software_sclk_pin:U_1:PA5
spi_software_mosi_pin:U_1:PA7
spi_software_miso_pin:U_1:PA6
spi_speed:200000
run_current: 1.07
#hold_current: 0.5
interpolate:true
stealthchop_threshold:0
diag0_pin:!U_1:PC0
driver_SGT:1
[tmc2240 stepper_x]
cs_pin:U_1:PD2
spi_software_sclk_pin:U_1:PA5
spi_software_mosi_pin:U_1:PA7
spi_software_miso_pin:U_1:PA6
spi_speed:200000
run_current: 1.07
#hold_current: 0.5
interpolate:true
stealthchop_threshold:0
diag0_pin:!U_1:PB8
driver_SGT:1
[tmc2209 stepper_z]
uart_pin:U_1: PC5
run_current: 0.6
#hold_current: 0.17
interpolate: True
stealthchop_threshold: 9999999999
diag_pin:^U_1:PC12
driver_SGTHRS:130
[tmc2209 stepper_z1]
uart_pin:U_1: PB7
run_current: 0.6
#hold_current: 0.17
interpolate: True
stealthchop_threshold: 9999999999
diag_pin:^U_1:PA13
driver_SGTHRS:130
[heater_bed]
heater_pin: U_1:PB10
sensor_type:NTC 100K MGB18-104F39050L32
sensor_pin:U_1: PA0
max_power: 1.0
control = pid
pid_Kp=63.418
pid_Ki=1.342
pid_Kd=749.125
min_temp: -60
max_temp: 125
[heater_generic chamber]
heater_pin:U_1:PC8
max_power:1.0
sensor_type:NTC 100K MGB18-104F39050L32
sensor_pin:U_1:PA1
control = pid#watermark
pid_Kp=63.418
pid_Ki=1.342
pid_Kd=749.125
min_temp:-100
max_temp:65
[verify_heater chamber]
max_error: 300
check_gain_time:480
hysteresis: 5
heating_gain: 1
[verify_heater extruder]
max_error: 120
check_gain_time:20
hysteresis: 5
heating_gain: 1
[verify_heater heater_bed]
max_error: 200
check_gain_time:60
hysteresis: 5
heating_gain: 1
[fan_generic auxiliary_cooling_fan]
pin: U_1:PA8
shutdown_speed: 0.0
cycle_time: 0.0100
hardware_pwm: false
kick_start_time: 0.100
off_below: 0.0
[fan_generic chamber_circulation_fan]
pin:U_1:PC9
shutdown_speed: 0.0
cycle_time: 0.100
hardware_pwm: false
kick_start_time: 0.100
off_below: 0.0
[chamber_fan chamber_fan]
pin:U_1:PA4
max_power: 1.0
shutdown_speed: 0
kick_start_time: 0.5
heater:chamber
fan_speed: 1.0
off_below: 0
idle_timeout:60
idle_speed:1.0
[heater_fan hotend_fan]
pin:gpio25
max_power: 1.0
shutdown_speed:1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
off_below: 0
[heater_fan hotend_fan2]
pin:gpio11
max_power: 1.0
shutdown_speed:1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
off_below: 0
[controller_fan board_fan]
pin:U_1:PC4
max_power:1.0
shutdown_speed:1.0
cycle_time:0.01
fan_speed: 0.6
stepper:stepper_x,stepper_y
[fan_generic cooling_fan]
pin:gpio2
max_power: 1.0
shutdown_speed: 0
cycle_time: 0.0100
hardware_pwm: false
kick_start_time: 0.100
off_below: 0.0
[output_pin caselight]
pin: U_1:PC7
pwm: false
shutdown_value:1
value:1
[output_pin beeper]
pin:U_1: PA2
pwm: false
shutdown_value:0
value:0
[output_pin ctlyd]
pin:U_1: PA14
pwm: false
shutdown_value:0
value:0
[smart_effector]
pin:U_1:PC1
recovery_time:0
x_offset: 17.6
y_offset: 4.4
z_offset: 0.000001
speed:5
lift_speed:5
probe_accel:50
samples: 2
samples_result: submaxmin
sample_retract_dist: 5.0
samples_tolerance: 0.05
samples_tolerance_retries:5
[qdprobe]
pin:!gpio21
z_offset:0.000001
[bed_mesh]
speed:150
horizontal_move_z:7
mesh_min:20, 15
mesh_max:230, 23
probe_count:8,8
algorithm:bicubic
bicubic_tension:0.2
mesh_pps: 2, 2
vibrate_gcode:
Z_DOUDONG
[filament_switch_sensor fila]
pause_on_runout: True
runout_gcode:
M118 Filament tangle detected
event_delay: 3.0
pause_delay: 0.5
switch_pin:U_1:PC3
[resonance_tester]
accel_chip:adxl345
probe_points:
120, 120, 10
[gcode_macro_break]
# Used for cancel print in a macro
[idle_timeout]
timeout: 43200
[pause_resume]
[display_status]
[virtual_sdcard]
path: ~/gcode_files
#*#
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [input_shaper]
#*# shaper_type_x = zv
#*# shaper_freq_x = 51.4
#*# shaper_type_y = mzv
#*# shaper_freq_y = 43.8
#*#
#*# [adxl345]
#*# probe_pin = gpio9
#*# int_pin = int1
#*# tap_thresh = 3500
#*# tap_dur = 0.01
#*# speed = 20
#*# z_offset = -0.1
#*# samples = 3
#*# sample_retract_dist = 10.0
#*# samples_result = median
#*# samples_tolerance = 0.05
#*# samples_tolerance_retries = 3
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.006052, 0.037067, 0.060270, 0.074177, 0.083317, 0.078395, 0.065192, 0.061755
#*# 0.016833, 0.023552, 0.041677, 0.056520, 0.063239, 0.069099, 0.071989, 0.087067
#*# 0.003786, 0.000739, 0.023239, 0.033474, 0.037927, 0.049567, 0.046599, 0.068395
#*# 0.018474, 0.022849, 0.035349, 0.033708, 0.041208, 0.043942, 0.037770, 0.054020
#*# 0.011833, 0.016599, 0.022067, 0.025661, 0.030505, 0.010661, -0.011917, 0.002380
#*# 0.031208, 0.040192, 0.041677, 0.043864, 0.042458, 0.021208, -0.002855, -0.005198
#*# 0.027067, 0.051520, 0.054802, 0.049645, 0.033630, 0.014411, -0.018245, -0.041761
#*# 0.036442, 0.064489, 0.087692, 0.077927, 0.063239, 0.033552, -0.018089, -0.067933
#*# tension = 0.2
#*# min_x = 20.0
#*# algo = bicubic
#*# y_count = 8
#*# mesh_y_pps = 2
#*# min_y = 15.0
#*# x_count = 8
#*# max_y = 229.97
#*# mesh_x_pps = 2
#*# max_x = 230.0
#*#
#*# [bed_mesh kamp]
#*# version = 1
#*# points =
#*# -0.019767, -0.018751, -0.025782
#*# -0.023751, -0.020392, -0.019063
#*# -0.028282, -0.019142, -0.020470
#*# tension = 0.2
#*# min_x = 111.12
#*# algo = lagrange
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 50.53
#*# x_count = 3
#*# max_y = 58.51
#*# mesh_x_pps = 2
#*# max_x = 119.11
#*#
#*# [bed_mesh ]
#*# version = 1
#*# points =
#*# -0.199689, -0.171876, -0.150470, -0.138282, -0.130548, -0.137579, -0.154532, -0.161485
#*# -0.196798, -0.187189, -0.170704, -0.158048, -0.151642, -0.148439, -0.146095, -0.133907
#*# -0.205079, -0.210157, -0.193439, -0.181642, -0.179454, -0.177032, -0.174064, -0.153204
#*# -0.193829, -0.189298, -0.178360, -0.175235, -0.171173, -0.174298, -0.180157, -0.167892
#*# -0.198673, -0.194376, -0.188360, -0.187657, -0.182814, -0.203907, -0.229845, -0.215157
#*# -0.181173, -0.167892, -0.170235, -0.168126, -0.172657, -0.192970, -0.220392, -0.224845
#*# -0.187345, -0.161095, -0.162189, -0.164610, -0.175314, -0.209064, -0.238517, -0.265782
#*# -0.183985, -0.148673, -0.126564, -0.135704, -0.148985, -0.181720, -0.239376, -0.291017
#*# tension = 0.2
#*# min_x = 20.0
#*# algo = bicubic
#*# y_count = 8
#*# mesh_y_pps = 2
#*# min_y = 15.0
#*# x_count = 8
#*# max_y = 229.97
#*# mesh_x_pps = 2
#*# max_x = 230.0
#*#
#*# [bed_mesh Lusra profile]
#*# version = 1
#*# points =
#*# 0.006052, 0.037067, 0.060270, 0.074177, 0.083317, 0.078395, 0.065192, 0.061755
#*# 0.016833, 0.023552, 0.041677, 0.056520, 0.063239, 0.069099, 0.071989, 0.087067
#*# 0.003786, 0.000739, 0.023239, 0.033474, 0.037927, 0.049567, 0.046599, 0.068395
#*# 0.018474, 0.022849, 0.035349, 0.033708, 0.041208, 0.043942, 0.037770, 0.054020
#*# 0.011833, 0.016599, 0.022067, 0.025661, 0.030505, 0.010661, -0.011917, 0.002380
#*# 0.031208, 0.040192, 0.041677, 0.043864, 0.042458, 0.021208, -0.002855, -0.005198
#*# 0.027067, 0.051520, 0.054802, 0.049645, 0.033630, 0.014411, -0.018245, -0.041761
#*# 0.036442, 0.064489, 0.087692, 0.077927, 0.063239, 0.033552, -0.018089, -0.067933
#*# tension = 0.2
#*# min_x = 20.0
#*# algo = bicubic
#*# y_count = 8
#*# mesh_y_pps = 2
#*# min_y = 15.0
#*# x_count = 8
#*# max_y = 229.97
#*# mesh_x_pps = 2
#*# max_x = 230.0
Популярные вопросы
Латунь или медь?
брак при печати тонких плоскостей
Kак в G-code Simplify3D изменить скорость печати Infill?
Есть какие либо...
Комментарии и вопросы
Нет, конечно. Для разовых моде...
Тут надо только понимать что и...
Прикольная, лайк. Но с креплен...
Приветствую всех, вот такой де...
может кто кратко подсказать ка...
Добрый день, при печати ABS пл...
Хотел спросить как исправить н...