прошивка anet v 1.5
Пытаюсь прошить марлин на anet a8 но выходит вот такая ошибка
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is 'E:3d printermarlinarduino-1.8.4hardware oolsavr/etc/avrdude.conf'
Using Port : COM20
Using Programmer : arduino
Overriding Baud Rate : 57600
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xd6
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x6f
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x80
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xbf
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xae
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xd6
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x02
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x21
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xcc
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xd6
avrdude done. Thank you.
Подскажите пожалуйста что я делаю не так.
Прошивал вот по этой статье https://3dtoday.ru/blogs/komandr/anet-a8-and-auto-calibration-or-manual-calibration-table-p1-migration-/ Плата Anet v 1.5
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is 'E:3d printermarlinarduino-1.8.4hardware oolsavr/etc/avrdude.conf'
Using Port : COM20
Using Programmer : arduino
Overriding Baud Rate : 57600
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xd6
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x6f
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x80
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xbf
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xae
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xd6
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x02
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x21
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xcc
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xd6
avrdude done. Thank you.
Подскажите пожалуйста что я делаю не так.
Прошивал вот по этой статье https://3dtoday.ru/blogs/komandr/anet-a8-and-auto-calibration-or-manual-calibration-table-p1-migration-/ Плата Anet v 1.5
Популярные вопросы
Оптимальное выставление высоты зазора от стола - Anet ET5 pro
Всем доброго времени суток! 4 месяца обладатель 3д принтера. Стол выставил в 0, по углам тоже несколько раз, автоуровень и щуп 0,1мм. Температура стол...
MKS TinyBee v1.0 первый самосбор
Здравствуйте! Начал сборку своего первого принтера и столкнулся с непонятным багом платы управления:
Зачем используют слово '3D' при описании аддитивных технологий?
Несколько раз уже я обращался к уважаемому сообществу с вопросом на тему - почему так говорят '3D печать', '3D принтеры' и прочие интерпретации, типа...
Комментарии и вопросы
Долго смотрел в сторону электр...
На айли, 3 день выставлены по....
Пины и ласточкин хвост тема. У...
Или же будут ли они вообще, т....
Нужна помощь. Не получается по...
Может есть у кого модель адапт...
Всем привет, может кто знает п...