Flying bear tornado 2 - печатает в воздухе.
Всё настроено, начинаю печать, головка позиционируется правильно, набирается температура, затем стол опускается на ~10 мм и начинается печать, печать в воздухе. В чем проблема?
Вот G-code из куры
;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M109 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z0 F{travel_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
;Put printing message on LCD screen
M117 Printing...
Вот G-code из куры
;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M109 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z0 F{travel_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
;Put printing message on LCD screen
M117 Printing...
Популярные вопросы
Покупка STL
Покупаете ли вы готовые STL-ки для печати? Или может готовые "киты", где не только stl, но и что-то еще? Если да, то что покупаете? Если нет, то почем...
Не делается ретракт при печати. Anycubic Kobra X
Здравствуйте, уважаемые!
Проблема:
При печати не происходит нормального ретракта, из-за чего всё в "паутине". Параме...
Проблема:
При печати не происходит нормального ретракта, из-за чего всё в "паутине". Параме...
Шестерня vs зубчатое колесо
Часто участникам портала приходится изготавливать зубчатые колеса и шестерни. Но мало кто задается вопросом, в чем их отличие?
Недавн...
Недавн...

Комментарии и вопросы
Пежня (кривая) с текстурами, о...
Скажите, какой разъём надо был...
Выложите что-то хорошее.
Привет! Сегодня я хочу спросит...
Всем привет!После обновления F...
имеется датчик и имеется принт...
Выручайте! Никак не могу настр...