Simplify3D после окончания печати, уходит в повтор.
Simplify3D по окончании, домой, и опять печатать рвется, останавливаю принудительно.
Старт:
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F9000 ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F9000;Put printing message on LCD screen
M117 Printing..0
Конец
M104 S0;extruder heater off
M140 S0;heated bed heater off (if you have it)
G91;relative positioning
G1 E-1 F300;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0;move X/Y to min endstops, so the head is out of the way
M84;steppers off
G90;absolute positioning
Старт:
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F9000 ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F9000;Put printing message on LCD screen
M117 Printing..0
Конец
M104 S0;extruder heater off
M140 S0;heated bed heater off (if you have it)
G91;relative positioning
G1 E-1 F300;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0;move X/Y to min endstops, so the head is out of the way
M84;steppers off
G90;absolute positioning
Популярные вопросы
Покупка STL
Покупаете ли вы готовые STL-ки для печати? Или может готовые "киты", где не только stl, но и что-то еще? Если да, то что покупаете? Если нет, то почем...
Проблема печати.
Добрый день , есть вопрос ))) У меня есть принтер он с завода оснащался белой тефлоновой трубкой. А сейчас я ее заменил на синюю и по моему с ней есть...
Вопрос по датчику Auto-leveling Sensor и g code
Всем добрый вечер!, купил датчик авто уровня , и теперь есть пару вопросов у тех кто таким пользовал, скажите его на горячую не льзя использовать я та...

Комментарии и вопросы
Здравствуйте. Если не ошибаюсь...
Вот и вопрос - на него вроде с...
эх, если бы нейронка не была б...
Прошу прощения за вопрос не по...
Подскажите пожалуйста есть у к...
Месяц назад угораздило меня&nb...
купил принтер бамбу лаб а1, та...