не работают концевики.
новая плата mks robin lite на дельта принтере . не отрабатывают концевики, просто упираются и дальше тыкают.
не могу понять в чем дело(
#============================== Endstop Settings ===========================
>MIN_SOFTWARE_ENDSTOPS 1 # 0:axes can move below MIN_POS; 1:axes won't move below MIN_POS.
>MAX_SOFTWARE_ENDSTOPS 1 # 0:axes can move below MAX_POS; 1:axes won't move below MIN_POS.
# Mechanical endstop with COM to ground and NC to Signal uses 'false' here (most common setup).
>X_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>Y_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>Z_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>X_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Y_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Z_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Z_MIN_PROBE_ENDSTOP_INVERTING 0 # set to true to invert the logic of the probe.
>FIL_RUNOUT_INVERTING 0 # set to true to invert the logic of the Filament Runout Sensor.
# Specify here all the endstop connectors that are connected to any endstop or probe.
>USE_XMIN_PLUG 1 # 1:used; 0:noused
>USE_YMIN_PLUG 1 # 1:used; 0:noused
>USE_ZMIN_PLUG 1 # 1:used; 0:noused
>USE_XMAX_PLUG 0 # 1:used; 0:noused
>USE_YMAX_PLUG 0 # 1:used; 0:noused
>USE_ZMAX_PLUG 0 # 1:used; 0:noused
не могу понять в чем дело(
#============================== Endstop Settings ===========================
>MIN_SOFTWARE_ENDSTOPS 1 # 0:axes can move below MIN_POS; 1:axes won't move below MIN_POS.
>MAX_SOFTWARE_ENDSTOPS 1 # 0:axes can move below MAX_POS; 1:axes won't move below MIN_POS.
# Mechanical endstop with COM to ground and NC to Signal uses 'false' here (most common setup).
>X_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>Y_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>Z_MIN_ENDSTOP_INVERTING 1 # set to true to invert the logic of the endstop.
>X_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Y_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Z_MAX_ENDSTOP_INVERTING 0 # set to true to invert the logic of the endstop.
>Z_MIN_PROBE_ENDSTOP_INVERTING 0 # set to true to invert the logic of the probe.
>FIL_RUNOUT_INVERTING 0 # set to true to invert the logic of the Filament Runout Sensor.
# Specify here all the endstop connectors that are connected to any endstop or probe.
>USE_XMIN_PLUG 1 # 1:used; 0:noused
>USE_YMIN_PLUG 1 # 1:used; 0:noused
>USE_ZMIN_PLUG 1 # 1:used; 0:noused
>USE_XMAX_PLUG 0 # 1:used; 0:noused
>USE_YMAX_PLUG 0 # 1:used; 0:noused
>USE_ZMAX_PLUG 0 # 1:used; 0:noused
Популярные вопросы
Слайсер урезает скорость 3д печати
Принтер Creality K2 SE, максимум может 500мм/с (мне хотя бы 100). В настройках слайсера указал скорость внешних, внутренних стенок 120мм/с, а при наре...
Покупка STL
Покупаете ли вы готовые STL-ки для печати? Или может готовые "киты", где не только stl, но и что-то еще? Если да, то что покупаете? Если нет, то почем...
нужна консультация
Решаю купить принтер, думаю но пока не решил какую выбрать конструкцию. На али нашел вот такой вариант ru.aliexpress.com/item/2016-Newest-TEVO-Tarant...

Комментарии и вопросы
Выложите что-то хорошее.
Согласен, и я именно об этом,....
К таким статьям неплохо было б...
Привет! Сегодня я хочу спросит...
Всем привет!После обновления F...
имеется датчик и имеется принт...
Выручайте! Никак не могу настр...