klipper проблема с платой. не видит ее клипер

стоит клипер

видит и шьет плату. 

printer.cfg

[include fluidd.cfg]

[virtual_sdcard]

path: /home/klipper/printer_data/gcodes

on_error_gcode: CANCEL_PRINT

[mcu]

serial: /dev/serial/by-id/usb-Klipper_lpc1768_0D0C020264015353ECF9F64C050000F5-if00

# This file contains common pin mappings for Smoothieboard. To use

# this config, the firmware should be compiled for the LPC176x.

# See docs/Config_Reference.md for a description of parameters.

[stepper_x]

step_pin: P2.0

dir_pin: P0.5

enable_pin: !P0.4

microsteps: 16

rotation_distance: 40

endstop_pin: ^P1.24

#endstop_pin: ^P1.25

position_endstop: 0

position_max: 200

homing_speed: 50

[stepper_y]

step_pin: P2.1

dir_pin: !P0.11

enable_pin: !P0.10

microsteps: 16

rotation_distance: 40

endstop_pin: ^P1.26

#endstop_pin: ^P1.27

position_endstop: 0

position_max: 200

homing_speed: 50

[stepper_z]

step_pin: P2.2

dir_pin: P0.20

enable_pin: !P0.19

microsteps: 16

rotation_distance: 8

endstop_pin: ^P1.28

#endstop_pin: ^P1.29

position_endstop: 0.5

position_max: 200

[extruder]

step_pin: P2.3

dir_pin: P0.22

enable_pin: !P0.21

microsteps: 16

rotation_distance: 33.500

nozzle_diameter: 0.400

filament_diameter: 1.750

heater_pin: P2.7

sensor_type: EPCOS 100K B57560G104F

sensor_pin: P0.24

control: pid

pid_Kp: 22.2

pid_Ki: 1.08

pid_Kd: 114

min_temp: 0

max_temp: 250

#[extruder1]

#step_pin: P2.8

#dir_pin: P2.13

#enable_pin: !P4.29

#heater_pin: P2.6

#sensor_pin: P0.25

#...

[heater_bed]

heater_pin: P2.5

sensor_type: EPCOS 100K B57560G104F

sensor_pin: P0.23

control: watermark

min_temp: 0

max_temp: 130

[fan]

pin: P2.4

[printer]

kinematics: cartesian

max_velocity: 300

max_accel: 3000

max_z_velocity: 5

max_z_accel: 100

[static_digital_output leds]

pins: P1.18, P1.19, P1.20, P1.21, P4.28

[mcp4451 stepper_digipot1]

i2c_address: 44

# Scale the config so that wiper values can be specified in amps.

scale: 2.25

# wiper 0 is X (aka alpha), 1 is Y, 2 is Z, 3 is E0

wiper_0: 1.0

wiper_1: 1.0

wiper_2: 1.0

wiper_3: 1.0

[mcp4451 stepper_digipot2]

i2c_address: 45

scale: 2.25

# wiper 0 is E1

wiper_0: 1.0

# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays

#[display]

#lcd_type: st7920

#cs_pin: P0.16

#sclk_pin: P0.15

#sid_pin: P0.18

#encoder_pins: ^P3.25, ^P3.26

#click_pin: ^!P1.30

а в fluidd 

плата mks sbase 1.3  хост - виртуалка на 11 дебиан

собственно я printer.cfg я изменил только id mcu 

что надо делать чтобы заработало ?