Еще одна проблема с осью Z

Добрых время суток

Не кто не знает золотую середину скорости оси Z

Испробовал (взяты с разных версий Марлина)

1,

#define DEFAULT_AXIS_STEPS_PER_UNIT {(200*16)/(2.0*20), (200*16)/(2.0*20), (200*16)/1.25, (3200*39.0)/(11.0 * 6.75 * 3.45)} // подходящее значение для начала подстройки на Prusa i3 Rework

#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)

#define DEFAULT_MAX_ACCELERATION {2000,2000,20,1000} // максимальное ускорение по отдельным осям

#define DEFAULT_ACCELERATION 3000 /// X, Y, Z and E max acceleration in mm/s^2 for printing moves

#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves

2,

#define DEFAULT_AXIS_STEPS_PER_UNIT {110.5,110.5,2560,78} // default steps per unit for ultimaker

#define DEFAULT_MAX_FEEDRATE {400, 400, 4, 45} // (mm/sec)

#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 3000 /// X, Y, Z and E max acceleration in mm/s^2 for printing moves

#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves

3,

//#define DEFAULT_AXIS_STEPS_PER_UNIT {(200*16)/(2.0*20),(200*16)/(2.0*20),200*16/7.75,(3200 * 39.0)/(11.0 * 6.75 * 3.45)} // default steps per unit for Ultimaker

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,400,96} // default steps per unit for Ultimaker

#define DEFAULT_MAX_FEEDRATE {200, 200, 5, 25} // (mm/sec)

#define DEFAULT_MAX_ACCELERATION {1000,1000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 3000 /// X, Y, Z and E max acceleration in mm/s^2 for printing moves

#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves

4,

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker

#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)

#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 3000 /// X, Y, Z and E max acceleration in mm/s^2 for printing moves

#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves

5,

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,774} // default steps per unit for Ultimaker

#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec)

#define DEFAULT_MAX_ACCELERATION {1500,1500,50,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 3000 /// X, Y, Z and E max acceleration in mm/s^2 for printing moves

#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts

#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves

а ось просто летает должна подниматся на 180 мм а поднимается до конца но показывает Z0.18.00

не пойму где загвоздка.