"Пропал" ретракт.

После некоторого перерыва в печати обнаружил, что в файлах, генерируемых слайсером, перестал работать ретракт (вместо него короткий звук заглохшего мотора).

Но если я генерирую g-код с сайта teachingtechyt.github.io (для калибровки), все работает нормально.

Подскажите пожалуйста, как это исправить?

Мой CONFIG.G:

; Configuration file for Duet WiFi (firmware version 1.21)

; executed by the firmware on start-up

;

; generated by RepRapFirmware Configuration Tool on Mon Aug 06 2018 00:13:45 GMT+0100 (IST)

; General preferences

G90 ; Send absolute coordinates...

M83 ; ...but relative extruder moves

M555 P1 ; Set firmware compatibility to look like RepRapFirmare

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.

M665 R105.6 L288 B105 H250 ; Set delta radius, diagonal rod length, printable radius and homed height

M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network

M550 PMy printer ; Set machine name

M552 S1 ; Enable network

;*** Access point is configured manually via M587

M586 P0 S1 ; Enable HTTP

M586 P1 S0 ; Disable FTP

M586 P2 S0 ; Disable Telnet

; Drives

M569 P0 S0 ; Drive 0 goes forwards

M569 P1 S0 ; Drive 1 goes forwards

M569 P2 S0 ; Drive 2 goes forwards

M569 P3 S0 ; Drive 3 goes forwards

M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation

M92 X80 Y80 Z80 E2727 ; Set steps per mm

M566 X370 Y370 Z1200 E40 ; Set maximum instantaneous speed changes (mm/min)(Jerk)

M203 X12000 Y12000 Z12000 E1200 ; Set maximum speeds (mm/min)

M201 X3000 Y3000 Z1000 E120 ; Set accelerations (mm/s^2)

M204 P4000 T2000 ; Set accelerations for print and travel moves (mm/s^2)

M906 X1000 Y1000 Z1000 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent

M84 S30 ; Set idle timeout

; Axis Limits

M208 Z0 S1 ; Set minimum Z

; Endstops

M574 X2 Y2 Z2 S1 ; Set active high endstops

; Z-Probe

M558 P5 R0.4 H2 F1200 T6000 ; Set Z probe type to effector and the dive height + speeds

G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height

M557 R90 S20 ; Define mesh grid

; Heaters

M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit

M305 P0 T100000 B4138 C0 R4700 ; *Set thermistor + ADC parameters for heater 0

M143 H0 S120 ; *Set temperature limit for heater 0 to 120C

M305 P1 B4725 C7.060000e-8 ; *Set thermistor + ADC parameters for heater 1

M143 H1 S280 ; *Set temperature limit for heater 1 to 280C

; Fans

M106 P0 S0 I0 F25000 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off

M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

M106 P2 S0 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools

M563 P0 D0 H1 F2 ; Define tool 0 + DEFAULT Fan0 ->forwarded to-> Fan2!!!

G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets

G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

; Miscellaneous

T0 ; Select first tool

M501 ; new commands override the ones earlier in your config.g

Г-код из teachingtechyt.github.io:

retraction.gcode

Г-код из слайсера:

mask_hook.gcode