Klipeer прогрев только стола, Кура, 3dtouch

Подскажите как сделать так чтобы 3dtouch начинал сканировать сразу после прогрева стола и лишь потом разогревался экструдер, а то у меня экструдер оставляет точки и сопли пластика на столе.

сейчас у меня такие настройки

стартовый код куры:

G28 ; home all axes

G92 E0

G1 E-5 F200

BED_MESH_CALIBRATE

G1 E5 F200

моя прошивка клипепера

[bltouch]

sensor_pin: P1.25

control_pin: P2.0

pin_move_time: 0.500

pin_up_reports_not_triggered: True

pin_up_touch_mode_reports_triggered: false

x_offset: 5

y_offset: 50

z_offset: -0.1

speed: 2

[force_move]

enable_force_move: True

[homing_override]

gcode: SET_KINEMATIC_POSITION Z=0

G0 Z10 F500

G28 X Y

G0 X108 Y170 F5000

G28 Z

axes: Z

[bed_mesh]

samples: 1

horizontal_move_z: 5

min_point: 20,75

max_point: 228,228

probe_count: 3,3

[stepper_x]

step_pin: P2.2

dir_pin: P2.6

enable_pin: !P2.1

step_distance: .00625

endstop_pin: ^P1.29

position_endstop: 228

position_min: 0

position_max: 228

homing_speed: 50

second_homing_speed: 10

[stepper_y]

step_pin: P0.19

dir_pin: P0.20

enable_pin: !P2.8

step_distance: .00625

endstop_pin: ^!P1.27

position_endstop: 232

position_min: 0

position_max: 232

homing_speed: 50

second_homing_speed: 10

[stepper_z]

step_pin: P0.22

dir_pin: !P2.11

enable_pin: !P0.21

step_distance: .00125

endstop_pin: probe:z_virtual_endstop

position_endstop: 234

position_min: 0

position_max: 234

homing_speed: 5

second_homing_speed: 2

position_min: -5

## Extruder configuration ##

[extruder]

step_pin: P2.13

dir_pin: P0.11

enable_pin: !P2.12

step_distance: .004878

nozzle_diameter: 0.400

filament_diameter: 1.750

heater_pin: P2.7

sensor_type: EPCOS 100K B57560G104F

sensor_pin: P0.24

control: pid

pid_Kp: 25.216

pid_Ki: 1.324

pid_Kd: 120.092

min_extrude_temp: 50

min_temp: 5

max_temp: 295

max_extrude_only_velocity: 40

max_extrude_only_accel: 10000

pressure_advance: 0.8

pressure_advance_lookahead_time: 0.020

#[extruder1]

#step_pin: P0.1

#dir_pin: P0.0

#enable_pin: !P0.10

#heater_pin: P2.4

#sensor_pin: P0.25

#...

## Heatbed configuration ##

[heater_bed]

heater_pin: P2.5

sensor_type: EPCOS 100K B57560G104F

sensor_pin: P0.23

control: pid

pid_Kp: 73.620

pid_Ki: 1.658

pid_Kd: 817.177

min_temp: 0

max_temp: 130

## Additional configuration ##

[fan]

pin: P2.3

[mcu]

serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00

[printer]

kinematics: corexy

# This option must be 'corexy' for corexy printers.

max_velocity: 200

max_accel: 3000

max_z_velocity: 10

max_z_accel: 50

square_corner_velocity: 5

## RepRapDiscount Full Graphic Smart Controller ##

[display]

lcd_type: st7920

cs_pin: P1.19

sclk_pin: P1.20

sid_pin: P1.18

encoder_pins: ^P3.26, ^P3.25

click_pin: ^!P0.28

[verify_heater heater_bed]

max_error: 130

check_gain_time: 90