Настройка концевиков SBASE
добрый день , помогите настроить концевики принтер ультитумбочка плата управления SBASE не видит концевики
с конфигом пока не очень разобрался , на экран TFT28 тоже не реагирует .
Подскажите что поправить в конфине (инфу не нашел по настройке)
Вот сам конфиг на концевики.
Спасибо.
Endstops
endstops_enable true # the endstop module is enabled by default and can be disabled here
#corexy_homing false # set to true if homing on a hbit or corexy
alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
alpha_max_endstop #1.25^ # NOTE set to nc if this is not installed
alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
alpha_min 0 # this gets loaded after homing when home_to_min is set
alpha_max 208 # this gets loaded after homing when home_to_max is set
beta_min_endstop #1.26^ #
beta_max_endstop 1.27^ #
beta_homing_direction home_to_max #
beta_min 0 #
beta_max 215 #
gamma_min_endstop #1.28^ #
gamma_max_endstop 1.29^ #
gamma_homing_direction home_to_max #
gamma_min 0 #
gamma_max 214 #
с конфигом пока не очень разобрался , на экран TFT28 тоже не реагирует .
Подскажите что поправить в конфине (инфу не нашел по настройке)
Вот сам конфиг на концевики.
Спасибо.
Endstops
endstops_enable true # the endstop module is enabled by default and can be disabled here
#corexy_homing false # set to true if homing on a hbit or corexy
alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
alpha_max_endstop #1.25^ # NOTE set to nc if this is not installed
alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
alpha_min 0 # this gets loaded after homing when home_to_min is set
alpha_max 208 # this gets loaded after homing when home_to_max is set
beta_min_endstop #1.26^ #
beta_max_endstop 1.27^ #
beta_homing_direction home_to_max #
beta_min 0 #
beta_max 215 #
gamma_min_endstop #1.28^ #
gamma_max_endstop 1.29^ #
gamma_homing_direction home_to_max #
gamma_min 0 #
gamma_max 214 #
Популярные вопросы
Klippper и все радости его конфигурации
такая проблема у меня голова по Y ходит нормально НО с осью Х возникла проблема она ездиет только по одной траектории ( ЖЕЛТАЯ НАРИСОВАНАЯ ЛИНИЯ) ...
Как закрутить правильно сопло.
Как на самом деле должно быть правильно закручено сопло?
Волнистые стенки.
С того момента как я собрал принтер Ultimaker уважаемого Plastmaski, не могу избавиться от одной проблемы. Уже почти 2 кг пластика перевел на тесты. М...
Комментарии и вопросы
Очень круто!
Ну шуруповёртом мотать не особ...
Я не замерял точно, но очень п...
Собственно попросили распечата...
Я начинающий, странное в куре....
При печати стали появляться шв...
Здравствуйте, друзья. Сталкива...