Не прошивается принтер Anet A8

Доброго времени суток.

Проблема заключается в том что больше не могу залить скетч в плату.

Последнее что заливалось так это прошивка Skynet v2.3.2 fix 2. После чего при включении принтера загружалось лого прошивки а далее пустой экран.

При по пытке повторно залить скетч выпадает ошибка.

avrdude: Version 6.3, compiled on Dec 16 2016 at 13:33:19

Copyright (c) 2000-2005 Brian Dean

Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is 'E:Skynet v2.3.2 fix 2arduino-1.8.0 (with APIM)hardware oolsavr/etc/avrdude.conf'

Using Port : COM14

Using Programmer : arduino

Overriding Baud Rate : 57600

AVR Part : ATmega1284P

Chip Erase delay : 55000 us

PAGEL : PD7

BS2 : PA0

RESET disposition : dedicated

RETRY pulse : SCK

serial program mode : yes

parallel program mode : yes

Timeout : 200

StabDelay : 100

CmdexeDelay : 25

SyncLoops : 32

ByteDelay : 0

PollIndex : 3

PollValue : 0x53

Memory Detail :

Block Poll Page Polled

Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------

eeprom 65 10 128 0 no 4096 8 0 9000 9000 0xff 0xff

flash 65 10 256 0 yes 131072 256 512 4500 4500 0xff 0xff

lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00

lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00

hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00

efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00

signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00

Programmer Type : Arduino

Description : Arduino

Hardware Version: 2

Firmware Version: 1.16

Vtarget : 0.0 V

Varef : 0.0 V

Oscillator : Off

SCK period : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e9705 (probably m1284p)

avrdude: reading input file 'C:UsersHOMEAppDataLocalTemparduino_build_789572/SkynetV2.3.2.ino.hex'

avrdude: writing flash (116608 bytes):

Writing |

avrdude: stk500_paged_write(): (a) protocol error, expect=0x14, resp=0x21

avrdude: stk500_cmd(): programmer is out of sync

Есть Arduino UNO (Китаец) Сделал ISP шнур для неё

Но при попытке зашить загрузчик получаю это:

E:Skynet v2.3.2 fix 2arduino-1.8.0 (with APIM)hardware oolsavr/bin/avrdude -CE:Skynet v2.3.2 fix 2arduino-1.8.0 (with APIM)hardware oolsavr/etc/avrdude.conf -v -patmega1284p -carduino -PCOM7 -b57600 -D -Uflash:w:C:UsersHOMEAppDataLocalTemparduino_build_789572/SkynetV2.3.2.ino.hex:i

avrdude: Version 6.3, compiled on Dec 16 2016 at 13:33:19

Copyright (c) 2000-2005 Brian Dean

Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is 'E:Skynet v2.3.2 fix 2arduino-1.8.0 (with APIM)hardware oolsavr/etc/avrdude.conf'

Using Port : COM7

Using Programmer : arduino

Overriding Baud Rate : 57600

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x1c

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x1c

avrdude done. Thank you.

Произошла ошибка при загрузке скетча